• |
欢迎来到广东联华智能装备股份有限公司官网
成立以来专注电动缸制造电缸、电动缸、伺服电缸、伺服电动缸制造生产厂家
电动缸厂家咨询电话:17328324199
您的位置:电缸知识 > 伺服电动缸知识 >
伺服电动缸知识

船舶用伺服电动缸的技术要求表

时间:2021-12-13 08:20:40 来源:创始人 点击:1次

  TECHNICAL DATA FORM FOR ELECTRIC CYLINDER SIZING电动缸技术数据采集表

船舶用伺服电动缸的技术要求表

  QUANTITY REQUIRED  需求数量 4

  MANDATORY DATA (if not filled-out, application sizing is NOT possible)必填数据(如果没有填写,电动缸型号将无法选出)Max load in push or pull mode (1)

  伸出或缩回状态下的最大负载 Kg 4000

  Working position (horizontal/vertical or angle)工作位置(水平/垂直或角度) Degrees (0° = horiz. | 90° = vert.)度(0°=水平| 90°=垂直) xx° 90°

  Only positioning or pushing at end of stroke (2)仅在行程结束时定位或推动 YES / NO是/否 YESWorking stroke of the system

  电动缸的工作行程 mm 约150

  Stroke at max load

  最大载荷时的行程 mm 40

  Speed in max load phase (3)

  最大负载时的工作速度 Consider for ramps, in case of short cycle.

  在短行程的情况下考虑斜坡 mm/sec 15

  Max required speed (3)

  最高要求速度 Consider for ramps, in case of short cycle.

  在短行程的情况下考虑斜坡 mm/sec 25

  Time for a complete working cycle

  一个完整循环的时间 (forward / backward)

  (向前/向后) sec 15

  Standstill brake needed

  是否需要应急操作 Typical for vertical axis垂直方向的标准值 YES / NO YES

  Motor needed

  是否需要电机 YES / NO YES

  Driver needed

  是否需要控制器 YES / NO YES

  (1) Load is the effective weight to move, PLUS the force to apply during the stroke or at the end.

  载荷是需要移动的负载重量,再加上在行程中或结束时施加的力(2) “NO” means that the cylinder keep pushing when reaching end-stroke (even if, for any reason, it cannot reach the pre-set quote).

  “否”表示电动缸在到达最终行程时继续推动(即使由于任何原因,它无法达到预设值)(3) If data are not available, please specify at least the working cycle time.

  如果数据不能提供,请至少给出循环工作时间。

  NON-MANDATORY DATA

  选填数据

  N. of cycles per minute

  每分钟循环次数 # 3

  Working hours per day

  每天工作时间/小时 # 1

  Requested positioning precision

  定位精度要求 +/- hundredths of mm

  +/-百分之一毫米 mm/100

  Anti-rotation

  防旋转 N = None; P = Present

  N =无; P =存在 N / P P

  Motor mounting, in line or parallel

  电机安装,串联或并联 L = In line; P = ParallelL =串联; P =并联 L / P L

  Protection class

  防护等级 N = IP44 ; S = IP65 N / S IP56

  Motor type

  电机类型 B = Brushless ; S = Stepper ; D = DC MotorB =无刷; S =步进; D =直流电机 B / S / D BQUICK DESCRIPTION OF THE APPLICATION / NOTES FOR THECNICAL DEPT.

  应用设备的描述/给技术部门的注释


本文链接:http://www.gzlhdg.com/sfddgzs113.html